GSO ISO 8178-9:2014
Gulf Standard
Current Edition
·
Approved on
25 December 2014
·
Reciprocating internal combustion engines -- Exhaust emission measurement -- Part 9: Test cycles and test procedures for test bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions
GSO ISO 8178-9:2014 Files
English
52 Pages
Current Edition
Reference Language
You can buy this standard from any member store
GSO ISO 8178-9:2014 Scope
This part of ISO 8178 specifies the measurement procedures and test cycles for the evaluation of smoke emissions from compression ignition engines on the test bed.
For transient smoke test cycles, smoke testing is conducted using smokemeters which operate on the light extinction principle. The purpose of this part of ISO 8178 is to define the smoke test cycles and the methods used to measure and analyse smoke. Specifications for measurement of smoke using the light extinction principle can be found in ISO 11614. The test procedures and measurement techniques described in Clauses 1 to 11 of this part of ISO 8178 are applicable to reciprocating internal combustion (RIC) engines in general. However, an engine application can only be evaluated using this part of ISO 8178 once the appropriate test cycle has been developed. Annexes A, B, E and F to this part of ISO 8178 each contain a test cycle that is relevant only for those specific applications listed in the Scope of that annex. Where possible, the smoke test cycle described in the annex utilizes the engine and machine categories developed in ISO 8178-4.
For certain categories of non-road engines “at site” rather than “test bed” smoke test procedures can prove to be necessary. For engines used in machinery covered by additional requirements (e.g. occupational health and safety regulations), additional test conditions and special evaluation methods can apply.
Best Sellers From Mechanical Sector
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 98:1988
Gulf Technical Regulation
MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 1780:2010
Gulf Technical Regulation
Motor vehicle-vehicle identification number (vin) - requirements
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ASTM D4778:2024
ASTM D4778:15
Gulf Standard
Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ASTM Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_astm_sml.png)
GSO ISO 24513:2024
ISO 24513:2019
Gulf Standard
Service activities relating to drinking water supply, wastewater and stormwater systems — Vocabulary
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO EN 14622:2024
EN 14622:2005
Gulf Standard
Devices to prevent pollution by backflow of potable water - Air gap with circular overflow (restricted) - Family A, type F
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO ISO 21384-2:2024
ISO 21384-2:2021
Gulf Standard
Unmanned aircraft systems — Part 2: UAS components
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)