GSO ISO 10684:2015
Gulf Standard
Current Edition
·
Approved on
03 September 2015
·
Fasteners -- Hot dip galvanized coatings
GSO ISO 10684:2015 Files
English
20 Pages
Current Edition
Reference Language
You can buy this standard from any member store
GSO ISO 10684:2015 Scope
This International Standard specifies material, process, dimensional and some performance requirements for hot dip spun galvanized coatings applied to coarse threaded steel fasteners from M8 up to and including M64 and for property classes up to and including 10.9 for bolts, screws and studs and 12 for nuts. It is not recommended to hot dip galvanize threaded fasteners in diameters smaller than M8 and/or with pitches below 1,25 mm.
NOTE Attention is drawn to the fact that the proof loads and stresses under proof load of oversize tapped nuts with threads M8 and M10 and the ultimate tensile loads and proof loads of undersize threaded bolts and screws with threads M8 and M10 are reduced as compared to the values specified in ISO 898-2 and ISO 898-1 respectively and are specified in Annex A.
It primarily concerns the spun hot dip galvanizing of threaded steel fasteners, but it may also be applied to other threaded steel parts.
The specifications given in this International Standard may also be applied to non-threaded steel parts such as washers.
Best Sellers From Mechanical Sector
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 98:1988
Gulf Technical Regulation
MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 1780:2010
Gulf Technical Regulation
Motor vehicle-vehicle identification number (vin) - requirements
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ASTM D4778:2024
ASTM D4778:15
Gulf Standard
Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ASTM Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_astm_sml.png)
GSO ISO 21384-2:2024
ISO 21384-2:2021
Gulf Standard
Unmanned aircraft systems — Part 2: UAS components
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 22407:2024
ISO 22407:2021
Gulf Standard
Metallic materials — Fatigue testing — Axial plane bending method
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 24513:2024
ISO 24513:2019
Gulf Standard
Service activities relating to drinking water supply, wastewater and stormwater systems — Vocabulary
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)