GSO ISO 16653-2:2016
Gulf Standard
Current Edition
·
Approved on
22 December 2016
·
Mobile elevating work platforms -- Design, calculations, safety requirements and test methods relative to special features -- Part 2: MEWPs with non-conductive (insulating) components
GSO ISO 16653-2:2016 Files
English
19 Pages
Current Edition
Reference Language
You can buy this standard from any member store
GSO ISO 16653-2:2016 Scope
This part of ISO 16653 specifies the design, calculations, safety requirements and test methods for mobile elevating work platforms (MEWPs) with non-conductive (insulating) components. It is intended to be used in conjunction with ISO 16368.
It is applicable to all types and sizes of MEWPs with non-conductive (insulating) components, including dielectric components designed and tested to meet the specific electrical properties consistent with the manufacturer's identification plate. This equipment is intended to move persons, tools and equipment to working positions where they can carry out work from a work platform located above a non-conductive boom section.
This part of ISO 16653 covers structural design calculations and the application of stability criteria, construction, safety examinations and tests done before MEWPs with non-conductive (insulating) components are first put into service. It identifies the hazards arising from the use of MEWPs with non-conductive (insulating) components and describes methods for the elimination or reduction of these hazards.
The MEWPs covered are not intended to have any of their components make contact with live parts of electrical installations. The electrical properties of a MEWP's non-conducting (insulating) components can provide electrical protection in case of inadvertent contact above the non-conductive boom component at the platform end. If a MEWP is equipped with a chassis insulating system, it can provide electrical protection for ground personnel in case of inadvertent contact above that system.
This part of ISO 16653 is not applicable to MEWPs designed for live working (see IEC 61057).
Best Sellers From Mechanical Sector
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 98:1988
Gulf Technical Regulation
MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 1780:2010
Gulf Technical Regulation
Motor vehicle-vehicle identification number (vin) - requirements
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ASTM D4778:2024
ASTM D4778:15
Gulf Standard
Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ASTM Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_astm_sml.png)
GSO ISO 24513:2024
ISO 24513:2019
Gulf Standard
Service activities relating to drinking water supply, wastewater and stormwater systems — Vocabulary
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO EN 14622:2024
EN 14622:2005
Gulf Standard
Devices to prevent pollution by backflow of potable water - Air gap with circular overflow (restricted) - Family A, type F
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO ISO 21384-2:2024
ISO 21384-2:2021
Gulf Standard
Unmanned aircraft systems — Part 2: UAS components
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)