GSO ISO 8132:2017
Gulf Standard
Current Edition
·
Approved on
03 October 2017
·
Hydraulic fluid power -- Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series
GSO ISO 8132:2017 Files
English
14 Pages
Current Edition
Reference Language
You can buy this standard from any member store
GSO ISO 8132:2017 Scope
This International Standard specifies the mounting dimensions required for the interchangeability of accessories for 16 MPa [160 bar] medium series cylinders in accordance with ISO 6020-1 and for 25 MPa (250 bar) series cylinders, in accordance with ISO 6022. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020-1 and ISO 6022, but this does not limit their application.
NOTE 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2
This International Standard covers the following accessories, identified in accordance with ISO 6099:
— AP2 — rod clevis, female thread (see Figure 1 and Table 1);
— AF3 — rod flange, circular (see Figure 2 and Table 2);
— AB4 — clevis bracket, straight (see Figure 3 and Table 3);
— AB3 — clevis bracket, in angle (see Figure 4 and Table 4);
— AT4 — trunnion bracket (see Figure 5 and Table 5);
— AA4-R — pivot pin, plain (cotter pin or snap ring type) (see Figure 6 and Table 6);
— AA4-S — pivot pin, plain (split pins) (see Figure 7 and Table 7);
— AA6-R — pivot pin, spherical bearing (cotter pin or snap ring type) (see Figure 6 and Table 6);
— AA6-S — pivot pin, spherical bearing (split pins) (see Figure 7 and Table 7);
— AP6 — rod eye spherical, female thread (see Figure 8 and Table 8);
— AP4 — rod eye plain, female thread (see Figure 9 and Table 9).
These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 3322.
This International Standard applies only to the dimensional criteria of products manufactured in conformity with this International Standard; it does not apply to their functional characteristics.
Best Sellers From Mechanical Sector
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 98:1988
Gulf Technical Regulation
MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 1780:2010
Gulf Technical Regulation
Motor vehicle-vehicle identification number (vin) - requirements
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ASTM D4778:2024
ASTM D4778:15
Gulf Standard
Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ASTM Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_astm_sml.png)
GSO ISO 24513:2024
ISO 24513:2019
Gulf Standard
Service activities relating to drinking water supply, wastewater and stormwater systems — Vocabulary
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO EN 14622:2024
EN 14622:2005
Gulf Standard
Devices to prevent pollution by backflow of potable water - Air gap with circular overflow (restricted) - Family A, type F
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO ISO 21384-2:2024
ISO 21384-2:2021
Gulf Standard
Unmanned aircraft systems — Part 2: UAS components
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)