GSO CEN/TR 13932:2023
Gulf Standard
Current Edition
·
Approved on
28 February 2023
·
Rotodynamic pumps - Recommendations for fitting of inlet and outlet on piping
GSO CEN/TR 13932:2023 Files
No files are available for this standard right now!
You can buy this standard from any member store
GSO CEN/TR 13932:2023 Scope
This CEN Technical Report lays down stipulations relating to installation conditions for sudden change in section or direction (elbows, tee fittings, junctions) and the most widely used accessories at the inlet and outlet of pumps (valves and fittings) in order to minimise the effect of disturbances in the flow of liquid thereby created upstream and downstream from the pump and on the operation of the pump.
NOTE 1 The recommendations given in this document permit to solve a majority of the most current cases.
These recommendations relate to three aspects of installation:
the fitting of the pump to pipework by convergent and divergent pipes;
in the case of elbows, tees and branching, their direction with respect to the axis of the pump;
the minimum clearances to be adhered to between a disturbing (elbow, valve, etc.) and the mounting flange of the pump.
This document applies to the installation of rot dynamic pumps (centrifugal, mixed flow and axial flow) fitted in piping. It applies to pumps having intake diameters equal to or less than 500 mm. The recommendations may be adapted in agreement with the pump manufacturer for intakes having dimensions exceeding 500 mm or for special applications. This document is not applicable to pumps of which the inlet is located in reservoirs, sumps or tanks and which will be dealt with in a subsequent standard.
The recommendations in this document are only valid under the following conditions:
Newtonian fluids having a maximum viscosity of 2.10-4 m2/s;
occluded gas content at pumping temperature and inlet pressure not exceeding 2 % by volume for water and
4 % for other fluids;
solids content (small particle size, such as sand) not exceeding 1 % by volume, nor 1 % by weight;
in piping with diameters D1 and D2 (see Figure 11), flow rate velocity, should be in the following ranges:
3 m/s to 5 m/s at inlet;
4 m/s to 10 m/s at outlet.
Best Sellers From Mechanical Sector
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 98:1988
Gulf Technical Regulation
MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 1780:2010
Gulf Technical Regulation
Motor vehicle-vehicle identification number (vin) - requirements
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ASTM D4778:2024
ASTM D4778:15
Gulf Standard
Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ASTM Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_astm_sml.png)
GSO ISO 21384-2:2024
ISO 21384-2:2021
Gulf Standard
Unmanned aircraft systems — Part 2: UAS components
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO BS 1212-2:2024
BS 12122:1990
Gulf Standard
Float operated valves - Part 2: Specification for diaphragm type float operated valves (copper alloy body) (excluding floats)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO ISO 11114-6:2024
ISO 11114-6:2022
Gulf Standard
Gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 6: Oxygen pressure surge testing
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)