GSO ISO 3958:2015
Gulf Standard
Current Edition
·
Approved on
03 September 2015
·
Passenger cars -- Driver hand-control reach
GSO ISO 3958:2015 Files
English
49 Pages
Current Edition
Reference Language
You can buy this standard from any member store
GSO ISO 3958:2015 Scope
1.1 This International Standard defines hand-reach envelopes: the boundaries of passenger car handcontrol locations that can be reached by different proportions of male and female driver populations. This International Standard applies to passenger cars (term 3.1.1 in ISO 3833:1977). It is primarily directed towards the initial design stages of a new vehicle programme. Its application for checking purposes in actual vehicle prototype seat models will take into account the allowable tolerances for the actual H-point and actual torso angle (see ISO/TR 9511).
The hand-reach envelopes apply directly to left-handdrive passenger cars designed for seated operators in full-width or single-width seats having approximately horizontal fore-and-aft seat adjustment. Application to right-hand-drive vehicles is assumed to be symmetrically opposite.
1.2 The envelopes constructed using the static three-point restraint described in the Introduction are meant to define a restrained reach. The envelopes constructed using lap belt only (type 1) are meant to define an unrestrained reach applicable to all restraint systems with free shoulder movement.
The hand-reach envelopes are directly applicable for a three-finger grasping reach to a forward-mounted control knob of 25 mm diameter manoeuvred horizontally in the fore-and-aft direction. The hand-reach envelopes are also applicable to other types of forward controls by using an appropriate adjustment factor that will account for the mode of operation of the control:
a) extended-finger-operated forward control: an adjustment factor of 50 mm is added to the values of the reach envelope in the appropriate table;
b) full-hand-g-asped forward control: an adjustment factor of 50 mm is subtracted from the tabled values of the reach envelope.
Best Sellers From Mechanical Sector
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 98:1988
Gulf Technical Regulation
MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 1780:2010
Gulf Technical Regulation
Motor vehicle-vehicle identification number (vin) - requirements
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ASTM D4778:2024
ASTM D4778:15
Gulf Standard
Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ASTM Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_astm_sml.png)
GSO ISO 21384-2:2024
ISO 21384-2:2021
Gulf Standard
Unmanned aircraft systems — Part 2: UAS components
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 22407:2024
ISO 22407:2021
Gulf Standard
Metallic materials — Fatigue testing — Axial plane bending method
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 24513:2024
ISO 24513:2019
Gulf Standard
Service activities relating to drinking water supply, wastewater and stormwater systems — Vocabulary
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)